Citroen C2 Rally Graphics (012)

Citroen C2 Rally Graphics (012)
Citroen C2 Rally Graphics (012)Citroen C2 Rally Graphics (012)Citroen C2 Rally Graphics (012)
Our Price:  £99.99
Main Colour:  
Additional Colour 1:  
Applicator Tool (squeegee):  

Model:  C2MSP0558
Brand:  Citroen C2

Citroen C2 rally motorsport side graphics, to suit all Citroen C2 cars.

Kit contents:

2 x large side designs, in separate pieces

Colours applied separately.

Trimming required around wheel arches.

This is a 2 colour rally graphics kit, shown on the silver Citroen C2 as black and red. Gaps in the design are clear so the cars background colour shows through.
Other colour combinations are available, please choose above:
Main colour: Black
Secondary colour: Red


Decal fitting

Fitting anything larger than a bumper sticker can be tricky for inexperienced fitters. For a guaranteed top class finish it is best to get your graphics fitted by a professional fitter, we have a list of partners below.

Wolverhampton based approved fitter:

Contact Brian at for prices & information.

Sutton Coldfield based approved fitter:

Contact Dave at for prices & information.

Derby based approved fitter:

Contact Henry at Evolve Automotive for prices & information.

North West Spain (Pontevedra):

Contact Rodney at Autovinilos for prices & information.


If you want to have a go at fitting the stickers yourself, below are some important tips and tricks below to help you get it right first time


Novice fitters often have problems with air bubbles getting trapped under the vinyl, spoiling the look of the stickers. Please note this is not a reflection of the quality of the vinyl, it is a fitting problem.


Many air bubbles will shrink and disappear after a while - vinyl is slightly porous and air will slowly leak from the bubbles in the same way air leaks out of a party balloon.

The best way to avoid air bubbles in the first place is to do a 'wet application' fitting method. Simply spray the prepared car surface with water before following the steps below. The water temporarily reduces the adhesion of the glue, and allows you to push both the water and air bubbles out using a squeegee applicator tool (or credit card). If you use too much water the vinyl will not stick to the car, simply wait for it to dry before trying to remove the application tape.

It is important to keep the backing paper dry - if water soaks into the backing paper it will cause paper fibres to stick to the adhesive on the vinyl.

This method can be used to apply stickers of any size or shape.

Before you start...

Make sure your car is clean. It has to be spotlessly clean, with all wax removed. Good prep is the most important part. Be careful attempting this job outdoors - a well timed gust of wind or stray flying insect can really spoil things.

Put your sticker in position and secure one end and the middle with masking tape.

Rub the transfer tape with your fingers to make sure the sticker binds to it securely. This is important as it makes the next step easier...

Slowly and carefully peel the backing away from the transfer tape.

Make sure that the sticker is stuck to the transfer tape and does not stay on the backing paper. See how we flip the decal over in step 2 and then peel the backing paper off. This is important and will help to make sure all letters are stuck to the transfer tape.

Take special care when your sticker has fine detail or lettering, as letters can tear or get left on the backing paper.

Using the scissors, trim off the loose backing paper as shown.

Give the surface another quick wipe to get rid of any unwanted dirt/dust/insects.

Then use the credit card or sign applicator to apply the sticker to the surface, working from the centre to the edge.

Remove the masking tape that held the sticker in position, fold the sticker over and peel off the rest of the backing paper as shown.

Again, take care doing this as you don't want to leave part of your decal still stuck to the backing paper!

After giving the surface a quick wipe, apply the rest of the sticker using the credit card, working from the centre to the edges as before.

Rub the sticker with the cloth to bind it to the vehicle, then slowly peel back the transfer tape to reveal your new fitted sticker.


Removing the stickers is easy, just pour scalding hot water on them and they will peel off in large chunks. The glue residue can be removed with meths, white spirit or any other solvent.


    Be the first to Write a Review for this item!